川消電控消防水炮需要進行消防聯動
來源:http://m.xintli.net/ 日期:2022-07-12
智能消防水炮成為大空間建筑的主要防火,滅火中堅力量;而另一重要的類別電控消防水炮,應用的場景不一樣,流量的大小不一樣,安裝的高度與智能消防水炮也不同,那么電控消防水炮需要不需要進行消防聯動呢?
Intelligent fire water cannon has become the main fire prevention and extinguishing backbone of large space buildings; Another important category is the electric fire water monitor. The application scenarios are different, the flow is different, and the installation height is different from that of the intelligent fire water monitor. Does the electric fire water monitor need fire linkage?
電控消防水炮的噴射介質是水,需要的額定壓力是0.8MPa,有壓力,免不了要使用消防水泵,使用消防水泵,就牽扯到如何啟動水泵,如果說在使用電控消防水炮前,先把水泵啟動起來,等到水炮用完,再去停止水泵,這種方式就直接成為***的手動了。所以電控消防水炮也需要聯動,在進行定位后,開啟電動閥的同時,消防水泵應該能夠自動聯動。
The injection medium of the electrically controlled fire water monitor is water, and the required rated pressure is 0.8MPa. If there is pressure, it is inevitable to use the fire water pump. Using the fire water pump involves how to start the water pump. If you start the water pump before using the electrically controlled fire water monitor, wait until the water monitor runs out, and then stop the water pump, this method will directly become * * * s manual. Therefore, the electric fire water monitor also needs linkage. After positioning, the fire water pump should be able to automatically linkage while opening the electric valve.
How is the linkage of Chuanxiao electric fire water monitor?
一、電控消防水炮具有五種控制方式,而需要噴水滅火就要打開電動閥,電動閥的控制方式在現場控制箱,或者遙控器,只需要將聯動信號連接在電動閥上信號端子就可以完成聯動。
1、 The electric fire monitor has five control modes, and the electric valve needs to be opened if it needs to spray water to extinguish the fire. The control mode of the electric valve is in the field control box or the remote controller. The linkage can be completed only by connecting the linkage signal to the signal terminal on the electric valve.

二、現場控制箱和遙控器的按鍵上面都有啟動水泵和停止水泵的按鍵,這個是怎么樣運行的呢,在水炮上有輸出的信號端子,可以直接連接到消防水泵,實現現場控制箱和遙控器同時啟動水泵后,再打開電動閥,保證水炮充足的供水壓力。
2、 There are buttons to start and stop the water pump on the buttons of the on-site control box and the remote controller. How does this work? There is an output signal terminal on the water monitor, which can be directly connected to the fire pump. After the on-site control box and the remote controller start the water pump at the same time, open the electric valve to ensure that the water monitor has sufficient water supply pressure.
電控消防水炮需要聯動消防水泵,而且超過150米遙控方式更簡單方便,遠距離只需要遙控水炮的炮口對準火焰,開閥就可以了,甚不用對準,直接開閥將水柱移動,更具有視覺震撼力;同時手動開啟霧狀,在一定情況下,效果會更好,比較經常需要降溫的地方,使用霧狀范圍大,降溫效果更好。
The electrically controlled fire water monitor needs to be linked to the fire pump, and the remote control method is more simple and convenient for more than 150 meters. For a long distance, it only needs to aim the muzzle of the remote control water monitor at the flame, open the valve, or even do not aim. Directly open the valve to move the water column, which is more visually shocking; At the same time, manually turn on the fog, and the effect will be better under certain circumstances. Where it is often necessary to cool down, the use of fog has a wide range and better cooling effect.
以上就是今天為大家介紹的關于問題以及注意事項的全部內容,希望對大家能有所幫助,想要了解更多內容可以電話聯系我們或者關注我們的網站
http://m.xintli.net,我們的工作人員會及時與您取得聯系。
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://m.xintli.net , our staff will contact you in time.