滅火器使用時的再充裝要點了解
來源：http://m.xintli.net/ 日期：2022-09-21
實際上，在補充滅火器時，應按照原始滅火器制造商的要求進行操作，要注意任何一種滅火器均不應變更充裝其他類型的滅火劑，下面
川消小編為您解答。
In fact, when replenishing the fire extinguisher, it should be operated according to the requirements of the original fire extinguisher manufacturer. It should be noted that any type of fire extinguisher should not be filled with other types of fire extinguishing agent. The following section of Chuanxiao will give you an answer.
重新填充的滅火劑應與原始滅火器制造商提供的滅火劑特性一致。重新裝填的滅火劑應滿足相關要求。
The refilled extinguishing agent shall have the same characteristics as those provided by the original extinguisher manufacturer. The refilled extinguishing agent shall meet relevant requirements.
加注之前，請清潔未更換的零件。除水基滅火器的各部分外，其他部分均應干燥。
Before filling, clean the parts that have not been replaced. Except for all parts of water-based extinguisher, other parts shall be dry.
ABC和BC干粉滅火劑灌裝設備應分開使用，并且灌裝地點應單獨分開。以確保不同類型的干粉滅火劑不會相互混合和交叉污染。
ABC and BC dry powder extinguishing agent filling equipment shall be used separately, and the filling site shall be separated. To ensure that different types of dry powder extinguishing agents do not mix and cross contaminate each other.
應使用專用的填充設備來填充滅火器。滅火器的填充量和填充密度應符合該模型。滅火器的填充要求應重新命名并一一確認，記錄下來。
Special filling equipment shall be used to fill the extinguisher. The filling quantity and filling density of the fire extinguisher shall conform to the model. The filling requirements of fire extinguishers shall be renamed, confirmed one by one and recorded.
儲存壓力滅火器中填充的驅動氣體應符合滅火器銘牌上規(guī)定的填充氣體和填充壓力的要求。填充氣體的壓力應在填充時根據(jù)填充物的環(huán)境溫度進行調整，并且在填充過程中不得使用。滅火器壓力指示器用作測量儀器，除水基滅火器外，驅動氣體的露點不得高于﹣55℃。
The driving gas filled in the storage pressure extinguisher shall meet the requirements of the filling gas and filling pressure specified on the nameplate of the extinguisher. The pressure of the filling gas shall be adjusted according to the ambient temperature of the filler during filling and shall not be used during filling. The pressure indicator of fire extinguisher is used as a measuring instrument. Except for water-based fire extinguisher, the dew point of driving gas shall not be higher than - 55 ℃.
用于滅火器的氣瓶應根據(jù)原始滅火器制造商的要求進行重新填充，或替換為原始制造商提供的已填充氣瓶。
Cylinders used for fire extinguishers shall be refilled in accordance with the requirements of the original fire extinguisher manufacturer or replaced with filled cylinders supplied by the original manufacturer.
Recharged stored pressure fire extinguishers or gas cylinders shall be subject to air tightness test one by one without bubble leakage. More relevant content will come to our website http://m.xintli.net Consult and understand!
