消防箱栓接頭有以下幾種安裝方式

來源：http://m.xintli.net/ 日期：2024-03-29

1、明裝采用6×M10鍍鋅膨脹螺栓固定，螺栓應均勻分布

1. The exposed installation is fixed with 6 × M10 galvanized expansion bolts, and the bolts should be evenly distributed

2、暗裝消火栓箱應采用水泥砂漿四周嵌密實，嚴禁使用混合砂漿填補。

2. Concealed fire hydrant boxes should be tightly embedded with cement mortar around them, and it is strictly prohibited to use mixed mortar to fill them.

3、消防箱在安裝過程中，應對消防箱內進行加固措施，以防變形。

3. During the installation process of the fire box, reinforcement measures should be taken to prevent deformation.

4、箱內管道和消火栓安裝時，在連接中應保護、防止箱內的油漆脫落。

4. When installing pipelines and fire hydrants inside the box, protection should be provided during the connection to prevent paint from falling off inside the box.

5、按立管位置預留進箱孔，嚴禁將其它未用敲落孔敲落，箱內的管道應橫平豎直。

5. Reserve entry holes according to the position of the riser, and it is strictly prohibited to knock off other unused holes. The pipes inside the box should be horizontal and vertical.

6、消防箱安裝完成時，應及時將敞開的箱門采用三夾板封閉;消火栓手柄閥門關緊后及時卸掉保存。

6. When the installation of the fire box is completed, the open box door should be promptly closed with three plywood; Remove and store the handle valve of the fire hydrant in a timely manner after it is tightly closed.

7、成品保護：安裝完成后及時處理表面污染并加以保護

7. Finished product protection: After installation, promptly handle surface pollution and provide protection

8、特殊部位安裝要求，為了確保裝修效果，走廊處的消防箱安裝必須與裝修緊密配合。

8. The installation requirements for special parts require that in order to ensure the decoration effect, the installation of fire boxes in the corridor must be closely coordinated with the decoration.

通常情況下，室外消火栓常見的地上栓是有三個接口的，兩個65MM口徑，一個100MM口徑，65MM口徑對應的是水帶的接口，通常為卡口，100MM口徑對應的是消防車吸水管，通常為螺紋的，不同的消防栓應使用相應的消防栓接頭規格，以上就是本文的全部內容。

In general, the most common outdoor fire hydrant above ground has three interfaces, two 65mm diameters and one 100mm diameter. The 65mm diameter corresponds to the interface of the water hose, usually a bayonet, and the 100mm diameter corresponds to the suction pipe of the fire truck, usually threaded. Different fire hydrants should use the corresponding specifications of the fire hydrant joint. The above is the entire content of this article.